Post by drdie on Oct 2, 2011 10:27:58 GMT -5
I run with the CA LWRC PSD. Well it went through a few changes over the last week.
Gear box: Upon checking the gear box it ended up with a few cracks in it from all the rounds put through it, about 40,000 to 50,000. Found out that the gearbox screws were loose. Thus causing the failure of the gear box shell. Probably should start checking them about every 25,000 rounds.
Went ahead and replaced the gear box shell and started fresh. Here is what Cromag put in it.
1.) Prometheus High speed gear set
www.crazycromags.com/prometheus-high-speed-gear-set-527.html
2.) Prometheus half tooth piston, works perfect when lined up properly with the gears.
www.crazycromags.com/prometheus-half-tooth-piston.html
3.) Prometheus piston head
www.crazycromags.com/prometheus-metal-piston-head.html
4.) Prometheus V2 Tappet Plate
www.crazycromags.com/prometheus-tappet-plate-version-2.html
5.) Prometheus 100 spring
www.crazycromags.com/prometheus-100-spring-no-liner.html
6.) Prometheus 247 X 6.03 Tight bore barrell
www.crazycromags.com/prometheus-6-03-247-mm-tightbore-barrel-g36-p90.html
7.) G&G Green bucking
www.crazycromags.com/g-g-bucking-internal.html
8.) AMP High torque Motor
www.crazycromags.com/amp-high-torque-motor-long.html
9.) ASCU MOSFET V2 W/4 programmable settings
www.crazycromags.com/ascu-mosfet-version2.html
We did install the systema turbo high speed motor, but it killed the 11.1V 1100 mah 15C stick battery in about 45 seconds. Still researching how to correct this and be able to run the systema motor. The rounds per second were just insane with this set up. I still want to test the CA high speed motor and see how that goes.
Even though we are using the AMP high torque motor the rounds per second are 27 to 28 with a 11.1V stick Lipo battery.
I have the ASCU Mosfet programmed on #1, this is safe, semi and three round burst. Right now the trigger response is so tight that I can be in three round burst and make it appear that the gun is in full auto.
The PSD chrono's at a mere 275 to 285 FPS. The PSD is very, very effective for the CQB environment. I would still like to put in a Prometheus 110 spring to bring the FPS to 340.
I will be installing the SCS nub when they become back in stock. I know this will increase the range a little and tighten up the grouping on my shots.
Gear box: Upon checking the gear box it ended up with a few cracks in it from all the rounds put through it, about 40,000 to 50,000. Found out that the gearbox screws were loose. Thus causing the failure of the gear box shell. Probably should start checking them about every 25,000 rounds.
Went ahead and replaced the gear box shell and started fresh. Here is what Cromag put in it.
1.) Prometheus High speed gear set
www.crazycromags.com/prometheus-high-speed-gear-set-527.html
2.) Prometheus half tooth piston, works perfect when lined up properly with the gears.
www.crazycromags.com/prometheus-half-tooth-piston.html
3.) Prometheus piston head
www.crazycromags.com/prometheus-metal-piston-head.html
4.) Prometheus V2 Tappet Plate
www.crazycromags.com/prometheus-tappet-plate-version-2.html
5.) Prometheus 100 spring
www.crazycromags.com/prometheus-100-spring-no-liner.html
6.) Prometheus 247 X 6.03 Tight bore barrell
www.crazycromags.com/prometheus-6-03-247-mm-tightbore-barrel-g36-p90.html
7.) G&G Green bucking
www.crazycromags.com/g-g-bucking-internal.html
8.) AMP High torque Motor
www.crazycromags.com/amp-high-torque-motor-long.html
9.) ASCU MOSFET V2 W/4 programmable settings
www.crazycromags.com/ascu-mosfet-version2.html
We did install the systema turbo high speed motor, but it killed the 11.1V 1100 mah 15C stick battery in about 45 seconds. Still researching how to correct this and be able to run the systema motor. The rounds per second were just insane with this set up. I still want to test the CA high speed motor and see how that goes.
Even though we are using the AMP high torque motor the rounds per second are 27 to 28 with a 11.1V stick Lipo battery.
I have the ASCU Mosfet programmed on #1, this is safe, semi and three round burst. Right now the trigger response is so tight that I can be in three round burst and make it appear that the gun is in full auto.
The PSD chrono's at a mere 275 to 285 FPS. The PSD is very, very effective for the CQB environment. I would still like to put in a Prometheus 110 spring to bring the FPS to 340.
I will be installing the SCS nub when they become back in stock. I know this will increase the range a little and tighten up the grouping on my shots.